Secondary scraper
The conveyor belt cleaners can be categorised afther more cathegories. After thei position, the cleaners can be: -primary scrapers, they are mounted on the drive pulley -secondary scrapers, they are mounted below the drive pulley -rotary cleaners, they are mounted after the secondary screaper, when is necesary -inside cleaner, they are mounted inside the belts, cleaning the bottom side of the belt
Pulley lagging
The pulley lagging is essential for a good work of the conveying system. For the pulley lagging we can use the Remaline group of products, which are smooth rubber sheets.
Chute lining
The chute lining, like the linings in general, are made from three reasons: to protect the chute agains wear, to prevent caking and for noise reduction. We have all the materials suitable for every application, which can solve all the above mentioned problems.
Remaskirt
REMASKIRT CB 195 is a special profiled rubber, makes an exceptionally good seal. The special sealing lips with their labyrinth effect keep transported material on the conveyor belt and reduce contamination and loss of material.
Impact bars
The impact bars are a combination of steel and rubber. The steel is a support for the rubber and facilitates the installation with the delivered screws. The impact bars are mounted, in the areas where are wear or noise problems due to impact.
Wear protection
Wear protection includes a wide range of applications. Rema Tip Top has developed different materials to cover all the applications. The surface protection can be made from various reasons, like wear problems, noise, caking, etc. Starting from the characteristics of the material, which is causes the problem, grain size, wet or dry, natural of sharp eged, we can determine the right material to protect the surface.
Pulley lagging
The pulley lagging is essential for a good work of the conveying system. For the pulley lagging we can use the Remaline group of products, which are smooth rubber sheets.
Remasleeve
The pulley lagging is essential for a good work of the conveying system. For the pulley lagging we can use the Remaline group of products, which are smooth rubber sheets.
Interior cleaner
The conveyor belt cleaners can be categorised afther more cathegories. After thei position, the cleaners can be: -primary scrapers, they are mounted on the drive pulley -secondary scrapers, they are mounted below the drive pulley -rotary cleaners, they are mounted after the secondary screaper, when is necesary -inside cleaner, they are mounted inside the belts, cleaning the bottom side of the belt
HDPE rollers
The TQ roller is the solution at locations where noise suppression is a problem. Acoustic measurements have shown that the reduction of ambient noise by 10 dB can be achieved, in comparison to traditional steel rollers.
Guiding rollers
Conveyor belts that run off-center cause spillage, loss of production and damage to the belt as well as the conveying system. REMA TIP TOP offers a perfect solution: The REMA Belt Tracker. Another high-quality product from REMA TIP TOP.
Round patch
Depending on the severity of the cuttings, punctures, the conveyor belts can be repaired. It is important the size and the location of the injury. A belt can be cutted transversal maximum 20% of the witdh of the belts, while a longitudinal cutting, theoretically can be repaired at any length. There are available repairing materials under different shapes like patches, with or without fabric reinforcement, which are developed for various types of reparations.
Conveyor belt repair
Depending on the severity of the cuttings, punctures, the conveyor belts can be repaired. It is important the size and the location of the injury. A belt can be cutted transversal maximum 20% of the witdh of the belts, while a longitudinal cutting, theoretically can be repaired at any length. There are available repairing materials under different shapes like patches, with or without fabric reinforcement, which are developed for various types of reparations.
Conveyor belt splicing
Conveyor belt splicing can be made in three ways: - First type is the classic vulcanization, called:”hot vulcanization” which is made with a vulcanizing press at a temperature of 145-155 °C. - The second vulcanization type is the “warm vulcanizing”. This type of vulcanizing is realized with special materials, developed by Rema Tip Top, called WK materials. The advantage of this material is that the vulcanizing process is made at 110 °C. This way the necessary time for a splicing is much sorter, the heating and cooling time beeing sorter.
Remasleeve
The pulley lagging is essential for a good work of the conveying system. For the pulley lagging we can use the Remaline group of products, which are smooth rubber sheets.
Rotary cleaners
The conveyor belt cleaners can be categorised afther more cathegories. After thei position, the cleaners can be: -primary scrapers, they are mounted on the drive pulley -secondary scrapers, they are mounted below the drive pulley -rotary cleaners, they are mounted after the secondary screaper, when is necesary -inside cleaner, they are mounted inside the belts, cleaning the bottom side of the belt
HDPE Rollers
The TQ roller is the solution at locations where noise suppression is a problem. Acoustic measurements have shown that the reduction of ambient noise by 10 dB can be achieved, in comparison to traditional steel rollers.
Secondary scraper
The conveyor belt cleaners can be categorised afther more cathegories. After thei position, the cleaners can be: -primary scrapers, they are mounted on the drive pulley -secondary scrapers, they are mounted below the drive pulley -rotary cleaners, they are mounted after the secondary screaper, when is necesary -inside cleaner, they are mounted inside the belts, cleaning the bottom side of the belt
Wear protection
Wear protection includes a wide range of applications. Rema Tip Top has developed different materials to cover all the applications. The surface protection can be made from various reasons, like wear problems, noise, caking, etc. Starting from the characteristics of the material, which is causes the problem, grain size, wet or dry, natural of sharp eged, we can determine the right material to protect the surface.
Remaskirt
REMASKIRT CB 195 is a special profiled rubber, makes an exceptionally good seal. The special sealing lips with their labyrinth effect keep transported material on the conveyor belt and reduce contamination and loss of material.
Pulley lagging
The pulley lagging is essential for a good work of the conveying system. For the pulley lagging we can use the Remaline group of products, which are smooth rubber sheets.
Primary scraper
The conveyor belt cleaners can be categorised afther more cathegories. After thei position, the cleaners can be: -primary scrapers, they are mounted on the drive pulley -secondary scrapers, they are mounted below the drive pulley -rotary cleaners, they are mounted after the secondary screaper, when is necesary -inside cleaner, they are mounted inside the belts, cleaning the bottom side of the belt
Profiled plates
The same like the impact bars, the plates, are a combination of steel and rubber. The steel is a support for the rubber and facilitates the installation with the delivered screws. The profiled plate is protecting against wear and has a noise reduction effect. The ideal situation is placeing the plates in 90° angle, in this angl the wear resitence of the rubber is the best.
Wear protection
Wear protection includes a wide range of applications. Rema Tip Top has developed different materials to cover all the applications. The surface protection can be made from various reasons, like wear problems, noise, caking, etc. Starting from the characteristics of the material, which is causes the problem, grain size, wet or dry, natural of sharp eged, we can determine the right material to protect the surface.
Remaskirt
REMASKIRT CB 195 is a special profiled rubber, makes an exceptionally good seal. The special sealing lips with their labyrinth effect keep transported material on the conveyor belt and reduce contamination and loss of material.
Remaslide
Remaslide is almost similar with the impact bars, but the plase of installation and thei utility is different. Remaslide bars are installed below the conveyor belt, at the impact area. They have in composition a metallic part, which ensures the easy installing with the dlivered screws, the rubber part which is the sock absorber and the upper part, which is a polyethylene layer, ensuring the sliding of the belt at moment of impact. The advantage of the impact bars to the impact rollers is that the bars can absorb much bigger sock, the thickness of the rubber can be up to 100mm.
